font_to_curve code was not handling properly the case where it has nop
object to check for mat indices validity. Check should just not happen
then, not reset mat indices of chars to default 0 value.
Convention was not to but after discussion on 918941483f we agree its
best to change the convention.
Names now mostly follow RNA.
Some exceptions:
- Use 'nodetrees' instead of 'nodegroups'
since the struct is called NodeTree.
- Use 'gpencils' instead of 'grease_pencil'
since 'gpencil' is a common abbreviation in the C code.
Other exceptions:
- Leave 'wm' as it's a list of one.
- Leave 'ipo' as is for versioning.
BF-admins agree to remove header information that isn't useful,
to reduce noise.
- BEGIN/END license blocks
Developers should add non license comments as separate comment blocks.
No need for separator text.
- Contributors
This is often invalid, outdated or misleading
especially when splitting files.
It's more useful to git-blame to find out who has developed the code.
See P901 for script to perform these edits.
Sometimes the text doesn't fit. What to do in this case?
* Overflow: The default behaviour still is to overflow the text.
* Truncated: If any text box is defined we can also not draw the text
that goes outside the text boxes.
* Scale to Fit: For single-text box texts we can scale down the text until
it fits.
To support textboxes we are bisecting the scale until we find a good
match. Right now the hardcoded iteration limit is 20, and the threshold 0.0001f.
An alternative in the future would be to tackle this by integrating existing
layout engines such as HarfBuzz.
Note: Scale to fit won't work for multiple text-boxes if any of them has
either width or height as zero.
Reviewers: campbellbarton
Differential Revision: https://developer.blender.org/D3874
Feature development sponsored by Viddyoze.
Terms get/set don't make much sense when casting values.
Name macros so the conversion is obvious,
use common prefix for easier completion.
- GET_INT_FROM_POINTER -> POINTER_AS_INT
- SET_INT_IN_POINTER -> POINTER_FROM_INT
- GET_UINT_FROM_POINTER -> POINTER_AS_UINT
- SET_UINT_IN_POINTER -> POINTER_FROM_UINT
As mentioned in d81aeb60fe the alignment for multiple text boxes should all
respect the same overall padding.
Vertical alignment is fully implemented now.
The original code was already making a distinction between lines in the last
text box and all lines. However I removed that bit since when I tested the
values were the same (I tested with a single text box).
Bringing this distinction back.
Not addressed here: All boxes should respect the alignment. Which at the moment
they don't seem to fully do.
They way Blender handles vertical alignment is very buggy:
- Top-Base: It works perfectly.
- Bottom: It is actually bottom-baseline,
and it fails when line size is != 1.0 when working with text boxes.
- Top: Poorly implemented, it should use font's ascent
(recommended distance from baseline),
so it has room for accents,
but it's not one line distance far from the origin (as it is now).
- Center: Poorly implemented.
This is tricky since there is no silver bullet.
To clear this situation I created a new option (Bottom-Baseline),
and addressed the issues above.
I'm getting the ascent and descent from freetype2,
and use this for padding above/below the text.
Also for vertically centering the text.
Solves these security issues from T52924:
CVE-2017-12102
CVE-2017-12103
CVE-2017-12104
While the specific overflow issue may be fixed, loading the repro .blend
files may still crash because they are incomplete and corrupt. The way
they crash may be impossible to exploit, but this is difficult to prove.
Differential Revision: https://developer.blender.org/D3002
Solves these security issues from T52924:
CVE-2017-12081
CVE-2017-12082
CVE-2017-12086
CVE-2017-12099
CVE-2017-12100
CVE-2017-12101
CVE-2017-12105
While the specific overflow issue may be fixed, loading the repro .blend
files may still crash because they are incomplete and corrupt. The way
they crash may be impossible to exploit, but this is difficult to prove.
Differential Revision: https://developer.blender.org/D3002
Annoyingly, need to convert vfont to nurbs, do minmax and toss nurbs away.
This is likely to be fine, since this function is not intended to be used
a lot, and this is the only way to get more meaningful result.
However, it's not very clear what to do with font on curve.
This fixes rendering of font object with auto texture space in Cycles
introduced in c34f3c7.
It is probably possible to introduce new mode to vfont_to_curve which
will do boundbox without extra allocations, but that's more like an
optimization.
Reviewers: campbellbarton, mano-wii
Reviewed By: campbellbarton
Subscribers: zeauro
Differential Revision: https://developer.blender.org/D2971
This will allow much finer controll over how we copy data-blocks, from
full copy in Main database, to "lighter" ones (out of Main, inside an
already allocated datablock, etc.).
This commit also transfers a llot of what was previously handled by
per-ID-type custom code to generic ID handling code in BKE_library.
Hopefully will avoid in future inconsistencies and missing bits we had
all over the codebase in the past.
It also adds missing copying handling for a few types, most notably
Scene (which where using a fully customized handling previously).
Note that the type of allocation used during copying (regular in Main,
allocated but outside of Main, or not allocated by ID handling code at
all) is stored in ID's, which allows to handle them correctly when
freeing. This needs to be taken care of with caution when doing 'weird'
unusual things with ID copying and/or allocation!
As a final note, while rather noisy, this commit will hopefully not
break too much existing branches, old 'API' has been kept for the main
part, as a wrapper around new code. Cleaning it up will happen later.
Design task : T51804
Phab Diff: D2714
Adding make_local for vfont/gpencil/group/freestyle linestyle/mask/scene/sound/text.
Note that there are still some lose ends here, since some type are not handled by id_copy
(Scene, Sound and VFont), which means in case a datablock of that type is used both
directly and indirectly, localization will fail.
Scene copying might be doable though (maybe with a simple new 'full shalow' mode to existing BKE_scene_copy?),
not sure about sounds and vfonts... Situations where this becomes an issue should be very rare corner cases anyway.
