This code was made obsolete by the changes to the animation editor
scrubbing areas in D4654.
Differential Revision: https://developer.blender.org/D7898
This tool is similar to the cloth brush, but it applies the cloth
simulation deformation to the whole mesh in an uniform way. The
simulation can be controlled using the mask to pin vertices and the face
sets to define force action areas.
It uses the same solver as the cloth brush which now no longer depends
on StrokeCache.
Reviewed By: sergey
Differential Revision: https://developer.blender.org/D7857
This Pose Brush origin mode simulates an FK deformation in the entire
model when clicking on the face sets, as they were controls of a fully
rigged character. Combined with the previous Face Sets modes that allow
creating IK chains, the pose brush should now be able to simulate most
of the common rigs deformations.
Reviewed By: sergey
Differential Revision: https://developer.blender.org/D7839
This was returning the wrong face set in cases where the active vertex
has more than one available face set.
Reviewed By: sergey
Differential Revision: https://developer.blender.org/D7858
The current name isn't very specific about what the operator does.
The operation is more about lining up the edges with the viewport
edges than centering the view.
Differential Revision: https://developer.blender.org/D7866
This applies a relatively simple solution for fixing some unintuitive
cases in unit handling.
Currently entering -1m50cm evaluates to -0.5m, and similarly 1'6"
evaulates to just half a foot. So effectively there's an implied + just
between the numbers, which is quite confusing.
This works by adding parentheses so the negative distributes to the
block of values before the next operator.
For example:
| Before | After |
| `-1m50cm + 1m -2m50cm` | `-(1m50cm) + 1m -(2m50cm)` |
| `-4m + 0.5 / -1.1` | `-(4m) + 0.5 / -(1.1)` |
| `-1'6"` | `-(1'6")` |
| `-1e-2cm` | `-(1e-2cm) ` |
Reviewed By: campbellbarton
Differential Revision: https://developer.blender.org/D7813
Toggling object mode to the previous wasn't working, also resolves a
case when toggling modes would cause an extra, unnecessary mode switch.
Own regression in 5159b8e1ea.
Make this consistent with meshes select side of active,
also rename "Under" to "Overlap" as this is confusing since
strips can be considered above/under each other
relative to their channels.
Add more descriptive warnings if building proxy fails.
Prevent progressbar from showing if no valid strip is selected.
Reviewed By: ISS
Differential Revision: https://developer.blender.org/D7689
Add `UNDER` option for `left_right` property of `sequencer.select` operator.
Add Equal as shortcut for select under playhead, and move Insert Gaps to backspace + ctrl.
Add extend shortcut for left, right under options.
The function is added to Select > Playhead menu.
Reviewed By: ISS
Differential Revision: https://developer.blender.org/D7679
This feature was a hack to prevent mmb select to print the orientation from menu in pre 2.80 versions.
Removing this feature as it is no longer an issue.
The Sculpt brushes were not properly initialized when use 2D template or other templates.
Also, using the default template (not factory settings) could be situations where the brushes were not updated.
This problem was introduced when some versioning code was removed in order to avoid duplicated brush creation.
This was introduced in rBd7282537f016 and had the wrong struct name
specified, leading to errors in writing/saving.
Stumbled over this when testing a color layer for pointclouds.
Differential Revision: https://developer.blender.org/D7882
Please note that vertices which are in a vgroup are not affected by this
option (which means that affected vertices from 'selection' modes remain
the same). Only the weights of selected vertices get inverted.
Reviewed By: mont29
Differential Revision: https://developer.blender.org/D7811
When setting the start cap of the array modifier it does not update when
updating the start cap objects geometry.
This patch switches the property update to rna_Modifier_dependency_update,
the same as the end cap which works properly.
Reviewed By: mont29
Differential Revision: https://developer.blender.org/D7584
The file subversion is no longer used in the Python API or user interface,
and is now internal to Blender.
User interface, Python API and file I/O metadata now use more consistent
formatting for version numbers. Official releases use "2.83.0", "2.83.1",
and releases under development use "2.90.0 Alpha", "2.90.0 Beta".
Some Python add-ons may need to lower the Blender version in bl_info to
(2, 83, 0) or (2, 90, 0) if they used a subversion number higher than 0.
https://wiki.blender.org/wiki/Reference/Release_Notes/2.83/Python_API#Compatibility
This change is in preparation of LTS releases, and also brings us more
in line with semantic versioning.
Fixes T76058.
Differential Revision: https://developer.blender.org/D7748
The ListBase next/prev pointers will change everytime you add or rename
an ID, also for 'neighbors' data-blocks in the list, causing unnecessary
'changed' detection.
This info is not needed in blendfile anyway, so just NULLify it.
There is no reason to have the children enable/disable state to
influence the parent collection. Specially considering that the parent
collection itself can have objects that would be visible.
Reviewed by: dfelinto, brecht
Differential Revision: http://developer.blender.org/D7864
